apple samsung LG htc hundai kia renault samsung gmdaiwoo audi bmw benz volkswagen honda infinity lexus nissan toyota volvo Chrysler jeep
비밀번호 확인 닫기
스마트폰/핸드폰 거치대 > Motorola > Droid(CDMA) > Motorola Droid (CDMA) 액티브 홀더
스마트폰/핸드폰 거치대


513090 Motorola Droid (CDMA) 액티브 홀더
제조회사 : Motorola
브랜드 : Droid (CDMA)
상품명 : Motorola Droid (CDMA) 액티브 홀더
모델명 : 513090
판매가격 : 92,400원
수량 EA
 
 
액티브 홀더
인스톨 설치형 케이블, 12V 2A 충전 아답터, Molex 타입 아답터 커넥터
 
 
  

 
상품 상세 설명
 
 
◆ 적용제품 ◆

Motorola Droid (CDMA)
Motorola Milestone

◆ 제품설명 ◆

An active holder which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior!

You can choose to use the holder as an active holder for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the holder also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection).

12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The holder is attached onto a tilt swivel so you can easily adjust your device in order to avoid light reflection. Attach onto a ProClip Mounting Platform.

◆ Instruction ◆

1.
2.
3.
4.


Please read all of the instructions and look at the pictures before attaching the holder. Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters.
Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.
Attaching the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate on desired position. Screw the attaching plate into place with the enclosed screws. Place the holder over the attaching plate so the tilt swivel fits. Screw the holder onto the attaching plate. The holder is in place. 3. Placing the device in the holder: Place the device next to the holder and slide it carefully sideways into the holder. Slide the device into the holder so you hear/feel it snaps into place. 4. The holder is in place, with a device in place. Switch easily between an upright, closed position and a horizontal, open position by turning the holder.
 
 
 
 
 
상품 사용 후기
 
 
이름 : 첨부 : 파일첨부
내용 :
평점
 
 
 
 
상품 QNA
 
상품에 대해 궁금한 점을 해결해 드립니다.
번호 제목 작성자 작성일 조회